Home

Low viscosity epoxy diluent

  • Benzyl Glycidyl Ether YLD-6021: Low-Odor Epoxy Diluent
    Benzyl Glycidyl Ether YLD-6021: Low-Odor Epoxy Diluent
    Nov 16, 2026
    Benzyl glycidyl ether YLD-6021 is a monofunctional aromatic diluent at 208-228 g/eq and 2-8 mPa·s, picked for potting when colour and chloride allow. At 20 phr it lifts blend EEW so amine demand falls, not rises; the same load brings 750 ppm hydrolyzable chloride, and that number settles the choice. Figure 1. YLD-6021 is a water-clear liquid; the published colour ceiling is APHA 50. 1. Introduction Viscosity limits most room-temperature epoxy work. A liquid bisphenol A resin such as YLE-128 runs at 11,000-15,000 mPa·s, too thick for potting fine windings or a brush coat without solvent. A reactive diluent lowers that figure and stays in the film. Several diluents in this catalogue bring that figure down, and choosing between them on viscosity alone is a mistake: functionality, colour ceiling and chloride load move with the choice. This report sets benzyl glycidyl ether YLD-6021 (CAS 89616-40-0) against three of them and states the arithmetic behind each decision. 2. Materials and Methods: Benzyl Glycidyl Ether YLD-6021 Specification 2.1 Product Identification The CAS number sits in the product page intro line, not the specification table. Table 1. Identity of benzyl glycidyl ether YLD-6021. Item Information Chemical name Benzyl glycidyl ether CAS No. 89616-40-0 Molecular formula C10H12O2 (calculated) Molecular weight 164.20 g/mol (calculated) Theoretical EEW 164.2 g/eq, one oxirane per molecule (calculated) Appearance Transparent liquid Package Drum 2.2 Specification Data and Test Methods Seven parameters are published, with no cure data and no thermal properties. Table 2. Published specification of YLD-6021 with the method applied to each parameter. Parameter Published value Method Colour, APHA Max. 50 APHA scale Viscosity at 25 °C, mPa·s 2-8 ASTM D445 EEW, g/eq 208-228 ASTM D1652, ISO 3001 Hydrolyzable chloride, % Max. 0.2 Titration Inorganic chlorine, ppm Max. 50 Titration Water, % Max. 0.1 ASTM E203 Epoxy equivalent weight is determined by titration according to ASTM D1652 or ISO 3001, water content according to ASTM E203. Viscosity is quoted at 25 °C; the page names no method, and ASTM D445 is the standard used across this catalogue. With no standard deviation or replicate count published, these figures are limits, not typicals. The published EEW of 208-228 g/eq sits well above the 164.2 g/eq calculated for the pure monomer, and that gap decides the arithmetic. A grade at 218 g/eq carries about three quarters of the epoxy content of the pure monomer; the rest is non-reactive. Substituting 164 overstates epoxy equivalents by a third, and the hardener weight follows. 3. Results and Discussion: Structure and Reactivity of Benzyl Glycidyl Ether 3.1 Why the Viscosity Falls So Far Benzyl glycidyl ether carries one oxirane ring on a short ether chain capped by a benzene ring, and no hydroxyl. That absence is why viscosity lands at 2-8 mPa·s. Bisphenol A resin is thick because its backbone hydroxyls hydrogen-bond; a benzyl ether has nothing to bond with. At 15 phr it takes a 13,000 mPa·s resin to about 4,660 mPa·s, the working range for casting small housings (Table 5). Reactivity is where the monofunctionality costs. Each molecule reacts once and stops, capping a chain end rather than extending the network, so crosslink density falls with the monofunctional fraction. The aromatic ring recovers part of that, and the page claims a high heat deflection temperature without publishing an HDT value to size it. 3.2 Selection Matrix Against Three Diluents Table 3 lines YLD-6021 up against three grades; all colour values are APHA, not Gardner. Table 3. Selection matrix: benzyl glycidyl ether YLD-6021 against three diluents, values as published on each product page. Property YLD-6021 YLD-6001 YLD-9004A Chemical type Benzyl glycidyl ether Glycidyl phenyl ether Butyl glycidyl ether Functionality 1 1 1 EEW, g/eq 208-228 Not published 147-157 Viscosity at 25 °C, mPa·s 2-8 2-8 Max. 2 Colour, APHA Max. 50 Max. 50 Max. 20 Hydrolyzable chloride Max. 0.2 % Not published Max. 0.1 % Effect on blend EEW Raises Raises Lowers The last two rows drive the pick. Difunctional 1,6-hexanediol diglycidyl ether YLD-6008 at 142-155 g/eq pulls blend EEW down and hardener demand up; YLD-6021 at 218 g/eq does the opposite. At 20 phr the two recipes need 12.9 phr against 11.5 phr, a gap no batch sheet shows. Odour and colour settle the rest. Butyl glycidyl ether YLD-9004A reaches max. 2 mPa·s at APHA 20, both better than YLD-6021, and pays with a sharper smell on an open line. Table 4 orders them by cost of getting them wrong. Table 4. Diluent decision sequence for a room-temperature bisphenol A system: condition, action, governing limit. Application condition Action Governing limit Ionic limit under 500 ppm Stop; settle the COA first 2,000 ppm hydrolyzable Cl Light or white topcoat Move to YLD-9004A APHA 50 vs APHA 20 Crosslink density first Use difunctional YLD-6008 Monofunctional capping Open pot, operators close Keep YLD-6021, skip the butyl Odour claim: neat liquid Target 3,000-5,000 mPa·s Set 15-20 phr Log mixing rule, coupon check Structural part over 20 phr Reduce loading or accept lower HDT A quarter of binder capped 4. Formulation and Dosage Calculation Once the grade is fixed, hardener demand follows the epoxy equivalents in the blend, not the resin mass alone. EEW(blend) = (100 + L) ÷ (100 ÷ EEW(resin) + L ÷ EEW(diluent)), with L as diluent loading in phr phr(amine) = 100 × AHEW ÷ EEW(blend) Table 5 applies both to liquid bisphenol A epoxy resin YLE-128 (EEW 184-190 g/eq, 11,000-15,000 mPa·s) with YLD-6021 at 0-30 phr. Viscosity comes from the logarithmic mixing rule, an approximation to check on a coupon before scaling. Table 5. Blend properties of YLD-6021 in YLE-128; viscosity estimated, hardener calculated at AHEW 20.6 g/eq. YLD-6021, phr Blend EEW, g/eq Viscosity, mPa·s DETA, phr blend DETA, phr resin 0 187.0 13,000 11.0 11.0 5 188.3 8,940 10.9 11.5 10 189.4 6,360 10.9 12.0 15 190.5 4,660 10.8 12.4 20 191.5 3,510 10.8 12.9 30 193.3 2,120 10.7 13.9 A 120 kg batch of 100 kg YLE-128 plus 20 kg YLD-6021 lands at 191.5 g/eq and takes 12.9 kg of diethylenetriamine at AHEW 20.6 g/eq, or 10.75 phr on blend mass. Both describe one recipe; quoting one without its basis is the usual dosing error at scale. Chloride scales with loading. At 20 phr the diluent brings about 40 g of hydrolyzable chloride into that batch against 50 g from the resin, near 750 ppm; at 30 phr, 846 ppm. With an ionic limit under 500 ppm neither loading passes, and the COA value has to be settled first. Twenty phr is a sensible ceiling for structural work. At 30 phr viscosity falls to 2,120 mPa·s, but a quarter of the binder is monofunctional and heat distortion shows it. 5. Processing Notes and Operating Window YLD-6021 disperses without high shear, which changes the sequence, not the equipment. Add the diluent to resin at 40-50 °C and stir slowly; high shear pulls in air that the liquid then holds. Weigh by mass. Density is not published, so a volume guess can be 5 % out and the EEW arithmetic with it. Keep the drum closed; a drum left open in a humid room picks up water, and 0.1 % is not generous. Do not hold a batch past gel time; a thin blend gives no visual warning. Figure 2. Diluent is metered into the resin by mass; low-shear mixing is enough at 2-8 mPa·s. A 20 phr blend holds less resin per unit volume, so a thick casting runs cooler while a thin film skins sooner. Re-check the cure schedule when loading changes. 6. Applications Three uses appear on the page, each loading following from Table 4. Table 6. Applications of YLD-6021, with the loading it supports and the governing limit. Application Role in the process Loading, phr Governing limit Electronic potting Cavity fill and wetting of windings 10-20 Hydrolyzable chloride budget Coating Solvent-free let-down for brush or roller 15-25 Colour ceiling at APHA 50 Construction adhesive Penetration into rough substrate 10-15 Chain termination at high load Figure 3. Potting a wound assembly: 10-20 phr of YLD-6021 brings a bisphenol A system into the 3,500-6,400 mPa·s range. Potting is the demanding case. A 20 phr blend at 3,510 mPa·s wets a winding in one pass, but it carries 750 ppm hydrolyzable chloride, and that number, not viscosity, decides insulation tests on high-impedance circuits. 7. Limitations and Material Verification 7.1 Where the Grade Does Not Fit Four limits rule uses out, each a selection filter. Monofunctional by design: a viscosity tool, not a crosslinker, and it will not carry a high-Tg formulation alone. Hydrolyzable chloride at max. 0.2 %, or 2,000 ppm, is the highest in its family; YLD-9004A allows 0.1 %. No thermal, mechanical or electrical data are published: no Tg, no HDT, no dielectric strength. EEW 208-228 g/eq against a theoretical 164.2 means composition is not fixed; check viscosity and EEW each lot. The 4-tert-butylphenyl glycidyl ether YLD-6004 page repeats the 2-methylphenyl description word for word, so verify that grade from its table alone. 7.2 Incoming Inspection, Packaging, Storage and Safety Incoming check covers viscosity at 25 °C, colour, water and EEW on the COA sample. Viscosity and EEW catch most off-spec lots; a wet batch shifts in viscosity before the water figure moves. Drums keep 12 months in original packing at ambient temperature, away from flame and sunlight. Safety data sits in the Material Safety Data Sheet; treat the liquid as a skin sensitiser until the MSDS says otherwise. No RoHS or REACH status is claimed here; that comes from the supplier's declaration. 8. Frequently Asked Questions When should YLD-6021 be chosen over another reactive diluent? Choose it when the ionic limit sits above 500 ppm, the topcoat is not colour-critical and Tg can give up a little: it is the only grade here that cuts viscosity while lowering amine demand. Move to YLD-9004A for APHA 20, or YLD-6008 when crosslink density beats flow. How much YLD-6021 should be added to an epoxy resin? Ten to twenty phr covers most work. At 20 phr a 13,000 mPa·s resin drops to 3,500 mPa·s; 30 phr reaches 2,120 mPa·s but makes a quarter of the binder monofunctional. Is YLD-6021 the same as butyl glycidyl ether? No. YLD-6021 is benzyl glycidyl ether, CAS 89616-40-0, at EEW 208-228 g/eq; YLD-9004A is butyl glycidyl ether, CAS 2426-08-6, at 147-157 g/eq. Both are monofunctional, but blend EEW moves opposite ways. Does YLD-6021 lower the glass transition temperature? Yes. Capping chain ends drops crosslink density and Tg together. How far depends on the hardener, since the page lists no Tg or HDT; the aromatic ring offsets part of it, and a coupon settles the rest. What chloride load does YLD-6021 bring into a potting compound? The specification allows max. 0.2 % hydrolyzable chloride, or 2,000 ppm. At 20 phr in a resin carrying 500 ppm the blend lands near 750 ppm; at 30 phr, 846 ppm. Can YLD-6021 replace solvent in a solvent-free coating? It can, and it stays in the film, so there is no flash-off step and no diluent VOC. Two constraints apply: hardness drops at high loading, and APHA 50 bars light topcoats that the butyl grade would pass. 9. Conclusions Benzyl glycidyl ether YLD-6021 cuts viscosity to 2-8 mPa·s while moving blend EEW up, so amine demand falls as loading rises — the reverse of difunctional grades. At 20 phr in YLE-128 the blend reaches 191.5 g/eq and 3,500 mPa·s, needing 12.9 kg of diethylenetriamine per 100 kg of resin. Selection then turns on two limits, not viscosity. Chloride at 2,000 ppm puts the blend at 750 ppm at 20 phr, ruling out high-impedance potting unless the COA comes lower; chain termination rules out structural parts above 20 phr. 10. References 1. Yolatech product page: https://www.yolatech.com/benzyl-glycidyl-ether-yld-6021 (accessed 2026-11-16). 2. Yolatech Technical Data Sheet (TDS) for YLD-6021, benzyl glycidyl ether, CAS 89616-40-0, on request. 3. Yolatech Certificate of Analysis (COA) for YLD-6021, batch values, on request. 4. ASTM D1652, epoxy content of epoxy resins (EEW). 5. ISO 3001, determination of epoxy equivalent. 6. ASTM D445, kinematic viscosity. 7. ASTM E203, water content by Karl Fischer titration.
    Read More
  • Bio-Based Epoxy Reactive Diluent: YLD-9016 Dosage Guide
    Bio-Based Epoxy Reactive Diluent: YLD-9016 Dosage Guide
    Oct 14, 2026
    Bio-based epoxy reactive diluent YLD-9016 is a difunctional cardanol diglycidyl ether specified at EEW 250-330 g/eq and 60-150 mPa·s at 25 °C. CAS 68390-54-5, non-volatile content 99.7% minimum, derived from cashew nut shell liquid. At 15 phr the diluent cuts a 13000 mPa·s resin to about 6300 mPa·s. Figure 1. Cardanol diglycidyl ether YLD-9016 is supplied as a light yellowish brown liquid with a Gardner color of 12 maximum and ships in 200 kg drums. 1. Introduction A high-solids epoxy formulation needs its viscosity cut by something that stays in the film. Solvent leaves as VOC; a reactive diluent cures into the network instead. That is the argument for glycidyl ethers. The cardanol line already covers three answers: cardanol glycidyl ethers YLD-9006 monofunctional at 30-50 mPa·s, and standard cardanol diglycidyl ether YLD-9014 with its variant YLD-9014A difunctional but at 1000-3000 mPa·s. Resin-class flow, not diluent-class flow. YLD-9016 publishes 60-150 mPa·s with two epoxy groups per molecule. It is the only grade in the family that pairs diluent-class viscosity with difunctional reactivity, on a cashew-derived backbone. Viscosity is only half the argument. Specification values below come from the public Yolatech product pages, derived constants are marked calculated, and dosage figures are worked examples. 2. Materials and Methods: Identification of Bio-Based Epoxy Reactive Diluent YLD-9016 Table 1 collects the identity and specification data published for YLD-9016. 2.1 Product Identification and Specification Table 1. Identity and published specification of bio-based epoxy reactive diluent YLD-9016. Item Information Product name Cardanol Diglycidyl Ether YLD-9016 Chemical family Cashew oil modified difunctional glycidyl ether CAS No. 68390-54-5 Appearance Light yellowish brown liquid Color, G Max. 12 EEW, g/eq 250-330 Viscosity (25 °C), mPa·s 60-150 Non-volatile, % Min. 99.7 Epoxy functionality 2 (bifunctional, as published) Raw material base Cashew nut shell liquid, plant-derived Packaging 200 kg drum Shelf life 12 months in original packing 2.2 Test Methods and Data Sources Table 1 reproduces the published figures without alteration. The report adds no laboratory data of its own. Epoxy equivalent weight is determined by titration under ASTM D1652 or ISO 3001, and the figure on the current TDS governs. Color is determined by ASTM D1544, and viscosity is measured at 25 °C under the method stated in the current TDS. Incoming checks on a glycidyl ether lot are typically run in duplicate, or as n = 3 determinations from separate positions in the drum. 3. Results and Discussion: Viscosity, Functionality and Dilution Behaviour Two published numbers separate YLD-9016 from the cardanol line: 60-150 mPa·s at 25 °C and 99.7% minimum non-volatile. 3.1 Structure and Reactivity of the Cardanol Backbone Cardanol is a meta-substituted phenol carrying a C15 unsaturated alkyl chain, obtained from cashew nut shell liquid. Capping that core with two glycidyl groups gives a rigid aromatic ring, a long hydrophobic tail and two reactive epoxide ends. Each part does one job. The epoxide ends consume amine and enter the network. The alkyl chain buys flexibility and water repellency. The aromatic ring lets a film harden at room and low temperatures. Nothing evaporates. A non-volatile content of 99.7% minimum means essentially the whole dose becomes part of the film. 3.2 Comparison with Alternative Systems Table 2 places YLD-9016 beside the petrochemical ethers it replaces and the sibling cardanol grades. Table 2. Property comparison of bio-based epoxy reactive diluent YLD-9016 with alternative reactive diluents (published values). Property YLD-9016 YLD-9014 AGE YLD-7003 BGE YLD-9004A HDDGE YLD-6008 Epoxy functionality 2 2 1 1 2 EEW, g/eq 250-330 290-350 294-313 147-157 142-155 Viscosity (25 °C), mPa·s 60-150 1000-3000 4-10 Max. 2 10-25 Raw material base Cashew, bio-based Cashew, bio-based Petrochemical Petrochemical Petrochemical Hardener demand vs 187 g/eq DGEBA Lowers Lowers Lowers Raises Raises   On raw thinning power the petrochemical ethers win: butyl glycidyl ether BGE YLD-9004 at 2 mPa·s maximum and 1,6-hexanediol diglycidyl ether YLD-6008 at 10-25 mPa·s, against 60-150 mPa·s. What they give back is hardener demand. At EEW 147-157 and 142-155 g/eq they pull a blend below the 184-190 g/eq of a standard bisphenol A resin, so every added part costs amine. YLD-9016 and alkyl (C12-C14) glycidyl ether YLD-7003 sit above 250 g/eq and push it down. Color limits are not comparable across the columns: the cardanol grades are limited in Gardner, the petrochemical ethers in APHA. Where a difunctional petrochemical ether is the incumbent, the product page names 1,4-butanediol diglycidyl ether YLD-6018L as a comparator, published at 98% minimum purity and no EEW window. 4. Formulation and Dosage Calculation Blend EEW and hardener demand follow two equations, with phr read as parts per hundred parts of resin by weight. Blend EEW = (100 + d) ÷ (100 ÷ EEW + d ÷ EEW9016), where d is the diluent loading in phr phr = 100 × AHEW ÷ EEW Table 3. Dilution and hardener dosage worksheet for 100 parts of bisphenol A epoxy resin YLE-128 at 187 g/eq and 13000 mPa·s, blended with YLD-9016 at its 290 g/eq and 105 mPa·s midpoints (calculated). YLD-9016 loading, phr Blend EEW, g/eq DETA phr at AHEW 20.6 MACM phr at AHEW 60 Viscosity estimate, mPa·s 0 187 11.0 32.1 13000 10 193 10.7 31.1 8400 15 196 10.5 30.6 6300 20 199 10.4 30.2 5800 Viscosity is estimated by a log-rule blend, which tracks glycidyl ether systems well enough for screening. A 15 phr loading takes an 11000-15000 mPa·s bisphenol A epoxy resin YLE-128 down to about 6300 mPa·s, a 51% cut. For a 1,000 g resin charge, weigh 150 g of YLD-9016 and 306 g of MACM curing agent at its published AHEW of 60 g/eq. Treat 30.6 phr as a starting point, because the 250-330 g/eq window is 80 g/eq wide. Dilution efficiency, not price, is the honest basis. No list price is published, so express the trade-off as viscosity reduction per phr and settle it against your own drum quotation. On that basis 15 phr of BGE reaches about 3500 mPa·s and wins on thinning, but YLD-9016 wins on volatile-free composition and hardener demand. If a formulation has to stay stiff, cap the loading near 20 phr and verify hardness development on the actual system. 5. Processing Notes and Operating Window Field practice with YLD-9016 reduces to five points. Add the diluent to the resin first and homogenize before the hardener enters; adding it after the amine invites stoichiometry errors. If a drum comes off a winter pallet, let it reach room temperature before reading viscosity, because the 60-150 mPa·s window is temperature-specific. Recalculate hardener phr from the lot COA each time a new drum arrives. Keep drums sealed between draws; glycidyl ethers absorb moisture slowly in humid storage, and water shows up later as blush. Run a gel-time check before locking pot life; difunctional diluents gel differently from the monofunctional ethers they replace. Figure 2. Diluent is poured into the resin and homogenized before the hardener is dosed, keeping the mix stoichiometry under control. 6. Applications The page lists high-solids and solvent-free coatings, adhesives and composites, plus surface alkylation of silica and titanium dioxide. Table 4. Application fit for bio-based epoxy reactive diluent YLD-9016 and the resin grades commonly blended with it. Application Why YLD-9016 fits Resin companion High-solids coatings Reactive dilution at 99.7% minimum non-volatile content YLE-128 Solvent-free 2K systems Co-cures into the network instead of leaving as emission YLE-170 Adhesives Flexibility, impact resistance and water resistance YLE-128 Composites and FRP Impregnation aid at diluent-class viscosity YLE-170 Filler surface treatment Alkylates silica and titanium dioxide surfaces None The coating logic runs through epoxy resin coatings: wherever a solvent-borne recipe converts to high solids, a reactive diluent with a negligible volatile fraction is the direct swap, but the hardener ratio still needs recalculating. Adhesive work is covered in epoxy resin adhesives, impregnation in epoxy resin composites. Figure 3. Solvent-free epoxy floor coating applied by roller, the application where reactive dilution replaces solvent entirely. 7. Limitations and Material Verification 7.1 Known Limitations and Unsuitable Cases Four specification gaps deserve confirmation before YLD-9016 is written into a purchase specification. Hydrolyzable chlorine, water content, density, flash point and molecular formula are not published; the grade gives only a non-volatile floor of 99.7%. Confirm them on the current TDS, MSDS and COA. The 250-330 g/eq EEW window is 80 g/eq wide, wider than the 184-190 g/eq of YLE-128. Batch drift inside it moves hardener demand by about 3% at a fixed loading. This grade is not the right choice for a stiff, heat-deflection-critical casting, and it is not a flame retardant: no halogen or phosphorus content is published. The food-grade statement appears on the YLD-9006 page, not here. Do not carry the claim across without written confirmation. 7.2 Incoming Inspection, Packaging, Storage and Safety Incoming inspection should confirm EEW by titration against the lot COA, plus color and non-volatile content. Reject a lot outside 250-330 g/eq. Packaging is a 200 kg drum with a stated shelf life of 12 months from manufacture in the original packing, stored cool and dry out of direct sunlight. Handling detail is carried by the Material Safety Data Sheet. Glycidyl ethers are skin sensitisers, so gloves and eye protection belong in the procedure. RoHS, REACH or UL 94 status has to be confirmed by the buyer against current certificates. A general product description implies no certification. 8. Frequently Asked Questions What is bio-based epoxy reactive diluent YLD-9016 made from? YLD-9016 is a cardanol diglycidyl ether derived from cashew nut shell liquid, with two epoxy groups per molecule. The page positions it as a non-toxic, renewable alternative to petrochemical ethers such as AGE and BGE. How is YLD-9016 different from YLD-9014 and YLD-9014A? The difference is viscosity. YLD-9016 runs at 60-150 mPa·s while YLD-9014 and YLD-9014A both sit at 1000-3000 mPa·s; all three share CAS 68390-54-5. How much YLD-9016 should be blended into a bisphenol A epoxy resin? Start between 10 and 20 phr. A log-rule estimate for 15 phr in an 11000-15000 mPa·s bisphenol A resin lands near 6300 mPa·s, and the right level depends on the stiffness the part can give up. Does YLD-9016 change the hardener dosage? Yes, downward. Its own EEW sits above the 184-190 g/eq of a standard bisphenol A resin, so each added part raises the blend EEW; at 15 phr the calculated MACM demand drops from 32.1 to 30.6 phr. Can YLD-9016 replace butyl glycidyl ether in a solvent-free coating? On thinning alone, no. BGE at 2 mPa·s maximum cuts deeper per phr and usually wins that comparison, so the swap makes sense when volatile content, odor or hardener demand carries more weight than the last third of the viscosity cut. Does YLD-9016 soften the cured coating? It adds flexibility by design, which is a trade rather than a defect. The alkyl chain lowers modulus and heat deflection while raising impact and water resistance, and the effect depends on the loading. 9. Conclusions Bio-based epoxy reactive diluent YLD-9016 is published at EEW 250-330 g/eq, 60-150 mPa·s at 25 °C, Gardner color 12 maximum and 99.7% minimum non-volatile content, in 200 kg drums with a 12-month shelf life. Its position is narrow but useful: diluent-class viscosity on a difunctional, cashew-derived backbone, with lower hardener demand than the petrochemical ethers it replaces. Dose by stoichiometry from the lot COA, cap the loading near 20 phr, and keep the deep-thinning monofunctional ethers for jobs that need them. 10. References 1. Product page, Cardanol Diglycidyl Ether YLD-9016, Yolatech: https://www.yolatech.com/cardanol-diglycidyl-ether-yld-9016 2. Product page, Cardanol Diglycidyl Ether YLD-9014, Yolatech: https://www.yolatech.com/cardanol-diglycidyl-ether-yld-9014 3. Product page, Butyl glycidyl ether BGE YLD-9004, Yolatech: https://www.yolatech.com/butyl-glycidyl-etherbge-yld-9004 4. Product page, 1,6-Hexanediol diglycidyl ether YLD-6008, Yolatech: https://www.yolatech.com/16-hexanediol-diglycidyl-ether-yld-6008 5. Product page, liquid bisphenol A epoxy resin YLE-127 / YLE-128, Yolatech: https://www.yolatech.com/bisphenol-a-epoxy-resin 6. Technical Data Sheet, Material Safety Data Sheet and Certificate of Analysis for Cardanol Diglycidyl Ether YLD-9016, Yolatech (available on request). 7. ASTM D1652 and ISO 3001, titration routes for epoxy content and epoxy equivalent weight. 8. ASTM D1544 for Gardner color, ASTM D445 for kinematic viscosity, ASTM E203 for water by Karl Fischer titration.
    Read More
  • Cardanol Glycidyl Ether YLD-9006: Bio-Based Reactive Diluent
    Cardanol Glycidyl Ether YLD-9006: Bio-Based Reactive Diluent
    Oct 02, 2026
    Cardanol glycidyl ether YLD-9006 is a bio-based monofunctional reactive diluent with viscosity 30-50 mPa·s at 25 °C and EEW 355-500 g/eq. It thins epoxy coatings, adhesives and potting compounds, and it comes from cashew nut shell liquid (CNSL). It carries one epoxide group on a C15 aliphatic chain.   Product Code: YLD-9006 — Cardanol Glycidyl Ether, monofunctional reactive diluentKey Raw Material: Cardanol from cashew nut shell liquid (CNSL) — CAS No. 171263-25-5Product Category: Reactive Diluent / Glycidyl Ether (Diluent & Glycidyl Ether line) 1. Product Information Item Information Product Name Cardanol glycidyl ethers YLD-9006 Chemical Family Glycidyl ether of cardanol, a C15 phenolic alcohol distilled from cashew nut shell liquid CAS No. 171263-25-5 Epoxide Functionality 1 — the product page describes YLD-9006 as a single epoxy-based active diluent Appearance Transparent liquid Primary Use Viscosity reduction in coatings, adhesives, potting and casting compounds, and composites Packaging Drum 2. Product Description: What Cardanol Glycidyl Ether YLD-9006 Does in an Epoxy System Cardanol glycidyl ether YLD-9006 is a reactive diluent, so it cures into the network instead of evaporating from the film. One epoxide group sits at the end of a C15 aliphatic chain, and that structure explains most of what you see at the bench. A single epoxide pushes the EEW up to 355-500 g/eq, which is high for a diluent, while the same long chain holds viscosity at 30-50 mPa·s at 25 °C. BGE reaches 147-157 g/eq by comparison, so the two products are not interchangeable gram for gram. Cardanol is distilled from cashew nut shell liquid, which makes YLD-9006 a renewable feedstock product rather than a petrochemical one. The phenol ring carries a C15 side chain that occurs naturally as a mixture of saturated, monoene, diene and triene forms. That mixture is why two drums of the same grade can differ slightly in colour and EEW, and why incoming EEW checks pay for themselves. Against fatty-chain monofunctional glycidyl ethers, the product page reports less impact on the thermal properties of the cured material, a clear toughening effect, and no irritating odour. The C15 chain acts as a built-in flexibilizer, so one additive delivers both viscosity reduction and impact improvement. YLD-9006 mixes well with aliphatic and aromatic epoxy resins, so it can be dropped into an existing high-solids coating or electronic potting formula without a compatibilizer. The product page also lists modified curing agents, a smaller outlet that few buyers ask about. 3. YLD-9006 Compared with Conventional Reactive Diluents Four diluents cover most of the market, and they are not interchangeable by weight because their epoxide contents differ threefold. The table below uses published data from the Yolatech product pages for each grade, so every row can be checked at source. Read the EEW column first, then viscosity; the first sets hardener consumption, the second sets how far it can thin a system. Attribute YLD-9006 (cardanol mono) YLD-7004 (C8-10 AGE) YLD-9004A (BGE) YLD-9014 (cardanol di) Epoxide groups 1 1 1 2 EEW, g/eq 355-500 220-250 147-157 290-350 Viscosity at 25 °C 30-50 mPa·s 3-10 mPa·s max 2 mPa·s 1000-3000 mPa·s Appearance Transparent liquid Transparent, APHA max 40 Transparent, APHA max 20 Reddish brown, colour G max 18 Hydrolyzable chloride max 0.5% max 0.2% max 0.1% not published Water max 0.1% max 0.1% max 0.5% max 0.2% Feedstock base CNSL, renewable C8-C10 synthetic alcohol Butanol CNSL, renewable Thermal effect on cured resin Less impact than fatty-chain mono diluents (supplier claim) Reference product for that claim Shortest chain, largest Tg drop Difunctional, adds crosslink density Toughening behaviour C15 chain flexibilizes Moderate None to slight High flexibility grade of the series Typical fit High-solids coatings, electronic potting Low-cost viscosity control Fast viscosity knock-down Flexible adhesives and sealants Weight-for-weight substitution is the most common mistake. Fifteen phr of BGE carries roughly 0.10 equivalents of epoxide, while the same loading of YLD-9006 carries about 0.04, so a straight swap leaves the mix under-cured unless the hardener is recalculated. If the requirement is crosslink density rather than viscosity, the monofunctional YLD-9006 is the wrong tool. Move to a cardanol diglycidyl ether YLD-9014 or the higher-flexibility cardanol diglycidyl ether YLD-9016, both of which carry two epoxide groups on the same renewable backbone. For a cost-driven viscosity cut on an unexposed substrate, a butyl glycidyl ether BGE YLD-9004 or a C8-10 alkyl glycidyl ether YLD-7004 costs less per unit of reduction. Workplace rules usually decide the rest. Many formulators have moved away from BGE for handling reasons rather than technical ones, so check the current SDS and your local exposure limits first. 4. Typical Technical Information of Cardanol Glycidyl Ether YLD-9006 The table below is the published specification for YLD-9006 and doubles as an incoming-inspection checklist. Item Specification Appearance Transparent liquid Viscosity at 25 °C 30-50 mPa·s EEW, g/eq 355-500 Hydrolyzable chloride Max. 0.5% Inorganic chlorine Max. 200 mg/kg Water Max. 0.1% Shelf life At least 12 months in original packing at ambient temperature These are typical values from the product page. Verify each lot against the TDS, MSDS and COA, and treat the EEW band as a range that drives hardener calculation rather than a fixed number. 5. Formulation and Selection Guidance A reactive diluent changes the epoxide equivalent weight of the blend, and the hardener dose follows that number. For two epoxy-bearing streams the mixing rule is simple: blend EEW = total mass divided by total epoxide equivalents. Hardener then follows phr = 100 × AHEW ÷ blend EEW, using the AHEW printed on the curing agent data sheet. Take a bisphenol F epoxy resin at EEW 170 g/eq and 3500-4500 mPa·s as the base, with a DMDC curing agent CAS 6864-37-5 at AHEW 60 g/eq as the hardener. Compare three blends at 15 phr diluent loading. Epoxy side Blend EEW, g/eq DMDC, phr Bisphenol F resin alone 170 35.3 Plus 15 phr YLD-9006 184 32.6 Plus 15 phr BGE YLD-9004A 167 35.8 The numbers use the mid-point of each published EEW band: 400 g/eq for YLD-9006 and 152 g/eq for BGE. Because YLD-9006 consumes less hardener per gram, a 15 phr addition lowers the DMDC demand by about 2.7 phr against the neat resin. That is a real cost offset that most buyers miss. Start at 5 phr and step up in 5 phr increments. Most formulators stop between 10 and 20 phr, because above that the monofunctional fraction acts as a plasticizer and pulls hardness, chemical resistance and glass transition temperature down. Viscosity does not fall in a straight line. A log-mixing estimate for the 15 phr blend above lands near 2000-2500 mPa·s at 25 °C, down from 3500-4500 mPa·s for the neat resin. Estimate only — in practice, confirm it with a laboratory reading on your own resin lot, since temperature and shear history both shift the result. 6. Processing Notes Most field problems trace back to loading, moisture or mixing order rather than to the diluent itself. • Add the diluent to the resin at 25-40 °C under low shear, then blend until uniform before charging filler or hardener. • Keep the drum sealed. The specification caps water at 0.1%, and an open drum in a humid season pulls headspace moisture that shows up later as a hazy film. • Never count YLD-9006 as solvent. It stays in the film and becomes part of the network, so solvent-release calculations do not apply. • Re-check EEW on arrival. Cardanol is a natural feedstock, so EEW shifts between lots and the hardener dose should follow it. • Store in a well-ventilated area, away from flames and direct sunlight, and close the cap tightly after use. • Watch pot life at high loading. More diluent extends pot life, which helps a short line and hurts a fast-cure process. • Measure mix viscosity at line temperature on composites work, because a diluent reading 40 mPa·s at 25 °C behaves differently in a 35 °C bath. 7. Applications of Cardanol Glycidyl Ether YLD-9006 The product page lists five application fields, and each one asks something different from the diluent. Application Role of YLD-9006 Field note High-solids coatings Cuts viscosity so solvent demand falls Watch sag resistance above 20 phr Electronic potting Low mix viscosity for void-free fill Confirm chloride limits with the customer Adhesives Toughening from the C15 chain Check peel strength, not just shear Casting compounds Improves flow around inserts Exotherm rises with batch size Composites, FRP winding Lowers bath viscosity for fibre wet-out Recheck bath viscosity as it ages Composites, pultrusion Improves impregnation of dense reinforcement Balance against green strength Modified curing agents Reactive building block, per the product page Develop in-house, not off the shelf Coatings and potting carry the volume, which is why the product page flags them first. For an epoxy resin coatings project, the diluent is the cheapest lever on volatile organic content, and it works in solvent-borne and solvent-free systems. On epoxy resin adhesives, YLD-9006 does two jobs at once: it thins the mix for better substrate wetting, and it leaves a flexible C15 segment in the cured bond line. Composite work is a different question. In epoxy resin composites, viscosity reduction only helps if it survives the run, so a bath that starts at 400 mPa·s and doubles over four hours ruins the last third of the batch. 8. Frequently Asked Questions What are the CAS number, EEW and viscosity of cardanol glycidyl ether YLD-9006? CAS No. 171263-25-5 belongs to cardanol glycidyl ether YLD-9006, which is published at EEW 355-500 g/eq with viscosity 30-50 mPa·s at 25 °C, with water capped at 0.1% and hydrolyzable chloride at 0.5% maximum. The EEW band is wide because cardanol is a natural feedstock, so plan the hardener dose around the actual lot value. Is YLD-9006 monofunctional or difunctional? It is monofunctional. The product page describes YLD-9006 as a single epoxy-based active diluent, and the EEW of 355-500 g/eq is consistent with one epoxide on a C15 chain. If the formulation needs crosslink density from the diluent, use a difunctional cardanol grade instead. How much YLD-9006 should be added, and does it change hardener dosage? Start at 5 phr and step up in 5 phr increments, with most systems settling between 10 and 20 phr. The hardener dose does change: at 15 phr the blend EEW rises from 170 to about 184 g/eq, and the DMDC requirement falls from 35.3 phr to 32.6 phr. Does YLD-9006 lower the glass transition temperature of the cured resin? Any monofunctional diluent lowers the glass transition temperature, and loading is the lever. The product page reports less impact on the thermal properties of the cured material than fatty-chain monofunctional diluents show, but that advantage shrinks as loading rises. Above 20 phr, expect a measurable drop. Can YLD-9006 replace BGE or C8-10 AGE at a 1:1 ratio? Not by weight. BGE sits at EEW 147-157 g/eq and C8-10 AGE at 220-250 g/eq, while YLD-9006 runs 355-500 g/eq, so an equal-weight swap changes the stoichiometry. Recalculate the hardener, then confirm that the higher mix viscosity still meets the process window. What is the shelf life and storage condition for YLD-9006? Shelf life is at least 12 months from the date of manufacture in the original packing at ambient temperature. Store the drum in a well-ventilated area away from flames and direct sunlight, and close the cap tightly after use; details sit in the MSDS. 9. Packaging, Storage and Safety YLD-9006 ships in drums and holds its specification for at least 12 months in the original packing at ambient temperature. Keep drums in a well-ventilated area, away from flames and direct sunlight, and reseal them tightly after every draw-off. Decant in a bunded area, wear nitrile gloves and eye protection, and follow the exposure limits on the MSDS. No certification should be assumed from this article. Flame-retardant, food-contact and electrical classifications depend on the finished formulation and cure schedule, not on the diluent alone, so test the cured part. Request the TDS, MSDS and COA for the shipping lot, and re-verify EEW, viscosity and water content on arrival.
    Read More

leave a message

leave a message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
submit

home

products

WhatsApp

Contact Us